a toaster component, a cooking chamber for warming up, broiling, baking and toasting (i.e. preparing/cooking) of food articles such as bread, pizza, hot dog, steak, sliced egg plant, potatoes, squash, egg, pancake and cookie is incorporated horizontally and below the main cavities of a standard “countertop toaster oven”, a standard “countertop microwave oven” and a standard “over-the-range microwave oven” comprising:
- (a) a toaster component cavity which is a short, deep and wide metal shell, having four steps on each, left and right, sidewalls;
- with front side open;
- houses all the required components to complete said toaster component and incorporated in the above mentioned appliances,
- (b) a drawer assembly comprising:
- (i) a tray, made out of solid sheet metal with multiple small perpendicular ears at its front having a small notch on top, where these ears allow the bent U-shaped sections on the front panel assembly slide over and lock the tray and the front panel assembly together;
- (ii) a wire rack, comprising a number of formed and straight metal wires with a small bend (bump) in the front and center where this bump will nestled inside a small cavity in the inner part of the front panel assembly and then locked when the U-shaped slide in the front panel assembly is lowered, and,
- (iii) a front panel assembly (the door), which the wire rack and the tray are perpendicularly attached to, covers said toaster component cavity's front opening during the cooking process;
- the front panel assembly has multiple bent U-shaped sections at the bottom, a small horizontal cavity at the center close to top and a two prongs slide moving up or down slightly to allow the bump in the wire rack enter or exit the small cavity;
- lowering the slide when the wire rack bump is nestled inside locks the two pieces together;
- the slide is held by shoulder screws which secure the slide while allow its vertical movement;
- the wire rack is the place that the food items are placed for cooking and tray is where the food particles and liquid (i.e. bread crumbs, meat juice/fat, pizza sauce/melted cheese, etc.) get collected;
- the wire rack and tray are perpendicularly attached to the front panel and this assembly slides in and out of the toaster component cavity as a single unit on the steps in the toaster component cavity side walls to prevent said food particles and liquids from dropping and spilling on the counter;
- the drawer panel closes the front opening of the toaster component cavity when the drawer assembly is pushed all the way in;
- the drawer assembly can be disassemble and reassemble without any tools for cleaning the tray or switching the wire rack with a griddle plate by pulling out drawer assembly several inches from closed position, pulling up the slide and pushing the wire rack all the way in followed by lifting the front panel assembly which disengages its bent U-shaped section from the tray ears which leaves either the tray or the wire rack easy to be pulled out;
- to reassemble the front panel assembly the tray is pushed into the toaster component cavity until several inches before reaching the end, then wire rack is pushed into the toaster component cavity all the way in;
- the front panel assembly is then lowered onto the tray ears until its bent U-shaped sections slide onto the tray ears and rest;
- the wire rack is then pulled forward until its bump nestles inside the small cavity on the inner surface of the front panel assembly;
- the tray and the front panel assembly will lock together when slide on the front panel assembly is lowered in place;
- (c) a top heat source, comprising standard toaster's heating element, nichrome wire, and standard insulating material, mica sheet, where nichrome wire is wrapped around the bottom surface of a large mica sheet with proper and equal spacing between each run and then assembled to the ceiling of the toaster component cavity, directly above the drawer assembly's wire rack;
- the top heat source extends from the front to the back wall and from the right sidewall to the left sidewall of the toaster component cavity to distribute heat evenly throughout the cavity duplicating the heat distribution of a standard toaster;
- the mica sheet prevents nichrome wire to contact metal ceiling of the toaster component cavity.
- (d) a bottom heat source, comprising standard toaster's heating element, nichrome wire, and standard insulating material, mica sheet, and a rectangular metal frame, where nichrome wire is wrapped around the top surface of a rectangular metal frame with proper and equal spacing between each run and insulated by stripes of mica;
- the mica stripes prevents nichrome wire to contact metal frame of the bottom heat source;
- the thin and narrow size and the spacing between each run of the nichrome wire allows the food particles and liquid to pass through the bottom heat source;
- the bottom heat source is positioned under the drawer assembly's wire rack and above its tray which allows the food particles and liquid to pass through and get collected in the tray;
- the bottom heat source extends from the front to the back and from the right sidewall to the left sidewall of the toaster component cavity to distribute heat evenly throughout the cavity duplicating the heat distribution of a standard toaster;
- and,
- (e) a drawer assembly release mechanism, comprising two small electro-mechanical spring loaded arms located on the lower part of left and right sides of the toaster component, pushing against the inner surface of the front panel of drawer assembly causing it to slightly open at the end of cooking cycle.